Project Phil's 1975 Honda Civic 1200
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Re: Phil's 1975 Honda Civic 1200
Hey Randy,Randy wrote: ↑November 1st, 2019, 1:29 pmHi Phil
I have been enjoying reading your posts on the Daily Digests that get emailed to me. But I just have to drop in to say what a nice job you are doing.
I am a bit confused on the bumper bolt tube you welded on. Are you missing the stock brackets? I know they can be pretty creaky.
Thanks for stopping by, appreciate the feedback!
The bumper bolt tube had a split in it so it's just a repair job. I'll get these painted up next week in a stealthy matte black finish, then onto the top bumper panel.
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Re: Phil's 1975 Honda Civic 1200
Now that I'm back at work the build progress is slowing down. I will do my best to keep up with documentation.
My good friend August recently returned from Japan with some rs gauges, that we won on yahoo jp. I look forward to getting these working in the not too distant future.
The front bumper is together. I painted the top indicator panel, bumper brackets and number plate bracket in satin black, and replaced all the hardware with new fasteners.
The gearbox is finally back together and tolerances are to specification. I decided to spend the last bit of spare time on the weekend preparing and painting the gearbox.
After completing the gearbox, we moved onto the rear main seal (which was 'fun' to get out). The unfortunate event was when the new seal cracked on first contact (apparently had been sitting on the shelf for 18 years). Have already organised a replacement.
I also have removed the exhaust completely now, ready for its replacement.
I've also started to pull the looms back into the engine bay and install a few accessories.
Exhaust manifold has returned from the ceramic coaters. Pleased. With the result.
My good friend August recently returned from Japan with some rs gauges, that we won on yahoo jp. I look forward to getting these working in the not too distant future.
The front bumper is together. I painted the top indicator panel, bumper brackets and number plate bracket in satin black, and replaced all the hardware with new fasteners.
The gearbox is finally back together and tolerances are to specification. I decided to spend the last bit of spare time on the weekend preparing and painting the gearbox.
After completing the gearbox, we moved onto the rear main seal (which was 'fun' to get out). The unfortunate event was when the new seal cracked on first contact (apparently had been sitting on the shelf for 18 years). Have already organised a replacement.
I also have removed the exhaust completely now, ready for its replacement.
I've also started to pull the looms back into the engine bay and install a few accessories.
Exhaust manifold has returned from the ceramic coaters. Pleased. With the result.
- mielko
- Projects
- Posts: 347
- Joined: January 5th, 2010, 12:39 pm
- Province/State: Europe,holland
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Re: Phil's 1975 Honda Civic 1200
So close I can nearly hear the engine purring. Pictures will speak louder than words here. Hammering out full weekends worth of work because I'm looking forward to driving again!
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Re: Phil's 1975 Honda Civic 1200
I went to test fit the radiator last week and found I had the incorrect clearance due to the tank bracket location. Without hassle, the local radiator shop adjusted the brackets for the correct fit.
In moving the the brackets, the fan needed to be spaced out from the core, so I ended up using a couple of nuts as spacers. The fan now has 2mm clearance from the core.
Outside of the workshop, I have removed the gauges from an old spare cluster to make room for my mechanical deluxe gauges. I cleaned the housing up using a basic car wash and rise method to remove the excess grime. I left the housing to dry overnight and proceeded to test a trim detailer in a inconspicious spot the following day. To my relief, it was an improvement over the original faded surface. upon confirmation, I continued to lightly apply the solution using a microfibre cloth to the remaining suface.
Unfortunately I do not have the centre pod gauges that belong to the deluxe set. As a temporary solution am planning to fabricate a pod or bracket to house the original temperature and fuel gauge. This could look great, but more likely extremely sketchy! Jay is sending me a mechanical tacho drive cable from the UK, so I can actually use them.
In moving the the brackets, the fan needed to be spaced out from the core, so I ended up using a couple of nuts as spacers. The fan now has 2mm clearance from the core.
Outside of the workshop, I have removed the gauges from an old spare cluster to make room for my mechanical deluxe gauges. I cleaned the housing up using a basic car wash and rise method to remove the excess grime. I left the housing to dry overnight and proceeded to test a trim detailer in a inconspicious spot the following day. To my relief, it was an improvement over the original faded surface. upon confirmation, I continued to lightly apply the solution using a microfibre cloth to the remaining suface.
Unfortunately I do not have the centre pod gauges that belong to the deluxe set. As a temporary solution am planning to fabricate a pod or bracket to house the original temperature and fuel gauge. This could look great, but more likely extremely sketchy! Jay is sending me a mechanical tacho drive cable from the UK, so I can actually use them.
- Steph
- Projects
- Posts: 3201
- Joined: August 14th, 2008, 2:02 am
- Province/State: South Australia
- Hometown: Adelaide
- Model: 1978 Hatchback
Re: Phil's 1975 Honda Civic 1200
Phil, you have to pull that engine brace off and paint it. You can actually buy them brand new as a complete unit made here in Australia. If that's not got new bushes in it don't waste your time with it. They're probably one of the single most 'consumable' bushes on the car IMO. When they start to go they stress the exhaust system too.
Oh yeah, p.s. and all that... NICE WORK!
Oh yeah, p.s. and all that... NICE WORK!
- mielko
- Projects
- Posts: 347
- Joined: January 5th, 2010, 12:39 pm
- Province/State: Europe,holland
Re: Phil's 1975 Honda Civic 1200
I see turbo'd engines in you garage.
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Re: Phil's 1975 Honda Civic 1200
I completely agree with the torque rod brace! I have one painted in cast iron sitting in the parts boxSteph wrote: ↑January 27th, 2020, 1:22 amPhil, you have to pull that engine brace off and paint it. You can actually buy them brand new as a complete unit made here in Australia. If that's not got new bushes in it don't waste your time with it. They're probably one of the single most 'consumable' bushes on the car IMO. When they start to go they stress the exhaust system too.
Oh yeah, p.s. and all that... NICE WORK!
For the time being i'm going to trial a urethane bush on the engine side, as a back-up I also got a new set off of Adrian.
Appreciate your advice
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
- Randy
- Administrator
- Posts: 1450
- Joined: April 7th, 2005, 9:06 pm
- Province/State: Ontario
- Hometown: Ajax
- Model: 1978 Hatchback
Re: Phil's 1975 Honda Civic 1200
Hey Phil
nice work, what is the metal bit for along the top?
nice work, what is the metal bit for along the top?
Welcome to the Site.