Project Bob78CVCC

Civic 1973-1979 Projects
Locked
Bill
LSD
LSD
Posts: 5554
Joined: December 16th, 2016, 7:52 am
Province/State: ….
Hometown: ….
Model: —————-

Post by Bill »

EF head is the same as the ED so there is no change of value there. Either use the 76 5 speed or the EK 82-83 5-speed... they are sorta at the ends of the spectrum, there are many more ratios in between, depending on the driving you want to do.
Top
User avatar
bob78cvcc
LSD
LSD
Posts: 1632
Joined: May 2nd, 2008, 9:22 pm
Province/State: NJ

Post by bob78cvcc »

Bill, the car will be used mostly for leisurely type driving and opening up a little on the hwy. The car rides on 13in rims 175/70 tires. Which 5 speed would work best under this scenario? Thanks again for your help. Bob :)
78 Civic CVCC

It's just a Civic thing :)
Top
Bill
LSD
LSD
Posts: 5554
Joined: December 16th, 2016, 7:52 am
Province/State: ….
Hometown: ….
Model: —————-

Post by Bill »

The 76-79 civic 5-speeds are a good easy installatioin for what you like to do , with the stock engine. The 5th gear is great for Fwy cruising and the 4th will pull the hills when you get to them. There is a transmission chart on the site that lists all the ratios, ... I just can't find it right now :roll: -someone will no doubt post it for you...
=Bill
Top
User avatar
bob78cvcc
LSD
LSD
Posts: 1632
Joined: May 2nd, 2008, 9:22 pm
Province/State: NJ

Post by bob78cvcc »

Here's some pics of the tear down. Easy to see just how damaged this engine was. :evil:
Attachments
Bent Rods.jpg
Bent Rods.jpg (66.54 KiB) Viewed 1177 times
Worn Rod Bearings.jpg
Worn Rod Bearings.jpg (63.13 KiB) Viewed 1177 times
Only #3 is good
Only #3 is good
Cylinder Head.jpg (68.92 KiB) Viewed 1177 times
#1 Cylinder Chamber Closeup.jpg
#1 Cylinder Chamber Closeup.jpg (62.25 KiB) Viewed 1177 times
#1 Cylinder Chamber.jpg
#1 Cylinder Chamber.jpg (82.93 KiB) Viewed 1177 times
#1 Cylinder - pitted.jpg
#1 Cylinder - pitted.jpg (57.13 KiB) Viewed 1177 times
78 Civic CVCC

It's just a Civic thing :)
Top
User avatar
Steph
Projects
Projects
Posts: 3150
Joined: August 14th, 2008, 2:02 am
Province/State: South Australia
Hometown: Adelaide
Model: 1978 Hatchback

Post by Steph »

Salvador Dali rods :lol:

That motor must have travelled a fair distance to wear the bearings like that?
Top
Bill
LSD
LSD
Posts: 5554
Joined: December 16th, 2016, 7:52 am
Province/State: ….
Hometown: ….
Model: —————-

Post by Bill »

Wow! Any idea what was banging around in the cylinder to cause all that hammering damage? You got some work ahead of you, but it is all doable... Parts search in your future. Good luck and have fun!
Top
User avatar
bob78cvcc
LSD
LSD
Posts: 1632
Joined: May 2nd, 2008, 9:22 pm
Province/State: NJ

Post by bob78cvcc »

Not sure what got smacked around in there. Boy, it sure left its marks. Going with the 1600 block and a different head. Don't want to bore the original block .20 over. :)
Attachments
Cylinder Tops (402 x 600).jpg
Cylinder Tops (402 x 600).jpg (59.13 KiB) Viewed 1147 times
78 Civic CVCC

It's just a Civic thing :)
Top
Bill
LSD
LSD
Posts: 5554
Joined: December 16th, 2016, 7:52 am
Province/State: ….
Hometown: ….
Model: —————-

Post by Bill »

Going with the 1600 and bump the compression a little and you will have a great running little car that will run on pump gas.!
Top
User avatar
TREVORM
LSD
LSD
Posts: 1477
Joined: April 13th, 2005, 5:06 pm
Province/State: Manitoba
Hometown: ...
Model: 1978 Hatchback

Post by TREVORM »

Steph wrote:Salvador Dali rods :lol:

:lol: :lol:
Trevor Marczylo l Photographer
Top
User avatar
bob78cvcc
LSD
LSD
Posts: 1632
Joined: May 2nd, 2008, 9:22 pm
Province/State: NJ

Post by bob78cvcc »

username wrote:Going with the 1600 and bump the compression a little and you will have a great running little car that will run on pump gas.!
Bill, if I go with the 75 flat pistons to bump up compression, will the engine still run on regular or will it need premium gas? How much of a bump is it? :)
78 Civic CVCC

It's just a Civic thing :)
Top
Locked

Return to “Projects and Builds”