Project Bob78CVCC

Civic 1973-1979 Projects
Locked
User avatar
bob78cvcc
LSD
LSD
Posts: 1632
Joined: May 2nd, 2008, 9:22 pm
Province/State: NJ

Post by bob78cvcc »

Steph wrote:Nice work Bob. It looks like there was/is a bit of rust to cut out there. Nothing worse than finding cancer.
Thanks, yea the cancer under the front of the right side rail is pretty nasty. It will be getting cut out and replaced.

Got a few moments to spray the inside steering rack hole area and the outside steering rack area. Taking a break to let it dry. These 40 degree days make the paint take a bit longer to dry. :)
Attachments
Steering Rack Hole Outside Civic (600 x 443).jpg
Steering Rack Hole Outside Civic (600 x 443).jpg (55.76 KiB) Viewed 1203 times
Steering Rack Hole Inside Civic (549 x 600).jpg
Steering Rack Hole Inside Civic (549 x 600).jpg (59.59 KiB) Viewed 1203 times
78 Civic CVCC

It's just a Civic thing :)
Top
User avatar
bob78cvcc
LSD
LSD
Posts: 1632
Joined: May 2nd, 2008, 9:22 pm
Province/State: NJ

Post by bob78cvcc »

Finally refinished the rear crossmember and am getting ready to reassemble it to the car. I'm happy with the undercoating and outer coat. I'm not quite sure which way to place the rubber grommet the pinion fits through (pic A or B). :)
Attachments
Rubber Grommet B.jpg
Rubber Grommet B.jpg (114.76 KiB) Viewed 1156 times
Rubber Grommet A.jpg
Rubber Grommet A.jpg (109.89 KiB) Viewed 1156 times
DSCN6265.jpg
DSCN6265.jpg (44.04 KiB) Viewed 1156 times
DSCN6264.jpg
DSCN6264.jpg (48.89 KiB) Viewed 1156 times
DSCN6268.jpg
DSCN6268.jpg (44.35 KiB) Viewed 1156 times
Rear Crossmember before refinishing
Rear Crossmember before refinishing
Steering rack - rear x-member (600 x 248).jpg (40.93 KiB) Viewed 1156 times
78 Civic CVCC

It's just a Civic thing :)
Top
User avatar
bob78cvcc
LSD
LSD
Posts: 1632
Joined: May 2nd, 2008, 9:22 pm
Province/State: NJ

Post by bob78cvcc »

Got the rear x-member and rack re-installed. The LCAs reconnected and the car is now back at the bodyshop to get the metal work done and the engine bay sprayed. :)
Attachments
Rear Xmember-Mount (600 x 304).jpg
Rear Xmember-Mount (600 x 304).jpg (52.31 KiB) Viewed 1128 times
Refinished Lower Firewall (600 x 291).jpg
Refinished Lower Firewall (600 x 291).jpg (43.14 KiB) Viewed 1128 times
78 Civic CVCC

It's just a Civic thing :)
Top
User avatar
Jonathan
LSD
LSD
Posts: 1397
Joined: May 16th, 2005, 6:56 pm
Province/State: Butler
Hometown: ...
Model: 1979 Hatchback CVCC

Post by Jonathan »

Looks good! Do you think you'll be ready for the Carlisle show this year?
Top
User avatar
bob78cvcc
LSD
LSD
Posts: 1632
Joined: May 2nd, 2008, 9:22 pm
Province/State: NJ

Post by bob78cvcc »

Jonathan wrote:Looks good! Do you think you'll be ready for the Carlisle show this year?
Very good question - assuming the engine is back in and running! :)
78 Civic CVCC

It's just a Civic thing :)
Top
User avatar
Steph
Projects
Projects
Posts: 3150
Joined: August 14th, 2008, 2:02 am
Province/State: South Australia
Hometown: Adelaide
Model: 1978 Hatchback

Post by Steph »

So what was the decision with the engine in the end Bob? Transplant or rebuild?
Top
User avatar
bob78cvcc
LSD
LSD
Posts: 1632
Joined: May 2nd, 2008, 9:22 pm
Province/State: NJ

Post by bob78cvcc »

Steph wrote:So what was the decision with the engine in the end Bob? Transplant or rebuild?
A rebuilt transplant consisting of an a 1600 EF bottom and a ED 1500 top. :)

The only thing I'll be keeping from the old engine are the 3 bent rods as a souvenier. :wink:
78 Civic CVCC

It's just a Civic thing :)
Top
User avatar
bob78cvcc
LSD
LSD
Posts: 1632
Joined: May 2nd, 2008, 9:22 pm
Province/State: NJ

Post by bob78cvcc »

Tomorrow might be paint day. :D Here's some pics of metal work & prep. :)
Attachments
DSCN6283.jpg
DSCN6283.jpg (77.27 KiB) Viewed 1036 times
DSCN6281.jpg
DSCN6281.jpg (53.6 KiB) Viewed 1036 times
DSCN6277.jpg
DSCN6277.jpg (45.58 KiB) Viewed 1036 times
DSCN6278.jpg
DSCN6278.jpg (44.71 KiB) Viewed 1036 times
78 Civic CVCC

It's just a Civic thing :)
Top
User avatar
Thor
LSD
LSD
Posts: 3594
Joined: November 30th, 2005, 8:05 am
Province/State: Stratford upon Avon
Model: —————-

Post by Thor »

Looking good
Good luck with the weather, ours is +4 deg tomorrow, just 40 degrees fartinheight :shock:
pete
Top
User avatar
Kurt
LSD
LSD
Posts: 2054
Joined: August 3rd, 2005, 12:56 am
Province/State: British Columbia
Hometown: Maple Bay
Model: —————-

Post by Kurt »

nice work. Those engine bays sure are a bietch to sand out arn't they :(
Top
Locked

Return to “Projects and Builds”