Build Kurts 1978 Honda Civic Trailer

Kurt · Post by **Kurt** » January 5th, 2014, 2:11 pm

May Long may be a bit ambitious but we'll see. So far its going quicker than I thought.

As for the gas, I thought of that too. My Ram has a 100 litre tank so I may just run it through it. I already need a new O2 sensors from running about 30 litres of Pre-Mix through it when I scrapped my jet ski this last summer :roll:

AHHVTEC · Post by **AHHVTEC** » January 7th, 2014, 5:41 pm

in for the build.

Oldie · Post by **Oldie** » January 7th, 2014, 7:03 pm

Kurt wrote:May Long may be a bit ambitious but we'll see.

You can do it Kurt!! Now my project fin date is end of June.Hoping( A BIG HOPING) to enter a second 1st Gen in the Atlantic Nationals this year!Only have the weekends to work on it thou. :( But i'am optimistic

)

Evoboy · Post by **Evoboy** » January 7th, 2014, 9:58 pm

Awesome can't wait will be following your progress!

DOHCIVIC · Post by **DOHCIVIC** » January 11th, 2014, 6:03 pm

Kurt wrote:
IMG_0078_1.JPG

IMG_0079_1.JPG

IMG_0082_1.JPG

IMG_0081_1.JPG

IMG_0084_1.JPG

IMG_0089_1.JPG

IMG_0089_1.JPG

IMG_0088_1.JPG

Look like you cut exactly where i cut
http://www.1stgencivic.com/forum/viewtopic.php?t=15143

XRTAYLORX · Post by **XRTAYLORX** » January 14th, 2014, 4:34 pm

this is awesome, now im gunna have to do one.

Meldge · Post by **Meldge** » January 14th, 2014, 8:56 pm

Ha ha, awesome. I have taken the tank out and cut my parts car in half but I have done nothing with it since.
I'm watching this one for sure as well.

Kurt · Post by **Kurt** » January 19th, 2014, 12:28 am

Did some more work today. Mostly more cutting to get rid of the front half. I should ask before I take it to the scrappers. Anyone need parts

Most the smaller pits were gone already but still have a nice grill. I cracked the perfect windshield taking it out :oops:

Saving the roof just for some 'free' sheet metal to weld up some holes in the trunk (I will post pics of that later). I also cut out a good section of one of the sills as I need to weld in a new section to the right side of the trailer half as its pretty rotted on that side. The outside panels on these are 22 guage (really thin) and the pillars (A and B) are 16 guage.

Hope to scrap the rest this week and I will see what they give me for the scrap! I have it in a small utility trailer for now but I may keep the 12" steel wheels as I keep throwing these out and have none left! The rear ones are 13" wheels from somewhere...

: IMG_0117_1.JPG (122.15 KiB) Viewed 3045 times

: IMG_0116_1.JPG (102.93 KiB) Viewed 3045 times

: IMG_0118_1.JPG (109.16 KiB) Viewed 3045 times

: IMG_0121_1.JPG (99.23 KiB) Viewed 3045 times

: IMG_0120_1.JPG (97.68 KiB) Viewed 3045 times

nathan · Post by **nathan** » January 19th, 2014, 2:16 pm

Nice work Kurt, lookin good.

Kurt · Post by **Kurt** » January 20th, 2014, 4:44 pm

Scrapped the rest of the car today. Got $54 for the scrap. I am into the car for $150 so only out a $100 so far.

I cut out two large pieces out of the roof to use the sheet metal to weld up some holes in the trunk. That will be my next task.

: IMG_0124_1.JPG (123.29 KiB) Viewed 3023 times

: IMG_0123_1.JPG (92.24 KiB) Viewed 3023 times

1StGenOfDurham

1StGenOfDurham

Build Kurts 1978 Honda Civic Trailer

Re: Honda Civic Trailer Build

Re: Honda Civic Trailer Build

Re: Honda Civic Trailer Build

Re: Honda Civic Trailer Build

Re: Honda Civic Trailer Build

Re: Honda Civic Trailer Build

Re: Honda Civic Trailer Build

Re: Honda Civic Trailer Build

Re: Honda Civic Trailer Build

Re: Honda Civic Trailer Build