Project MIELKO First Generation Civic SB1 from Holland
- mielko
- Projects
- Posts: 336
- Joined: January 5th, 2010, 12:39 pm
- Province/State: Europe,holland
Project MIELKO First Generation Civic SB1 from Holland
Hello,
I would like to introduce myself.
Im mielko
Live in Holland ,Europe
Date of birth,1978 ,6 january
What am i doing here?: Bothering you guy's with tech questions :D
As My old eb 1 is not equiped with ECU's ,inlet air sensors or lambda's .Its a bit of my knowledge.
These are the opel kadel rims,with i'm remaking,to fit 4*120 .
ATS classic 13" 6J wide
this is how i pay for my hobby's,I lighten flywheels,this is a "special i made for a friend.its a B16A2 ,With i lightend from 7,6 to 3,8kg.
I would like to introduce myself.
Im mielko
Live in Holland ,Europe
Date of birth,1978 ,6 january
What am i doing here?: Bothering you guy's with tech questions :D
As My old eb 1 is not equiped with ECU's ,inlet air sensors or lambda's .Its a bit of my knowledge.
These are the opel kadel rims,with i'm remaking,to fit 4*120 .
ATS classic 13" 6J wide
this is how i pay for my hobby's,I lighten flywheels,this is a "special i made for a friend.its a B16A2 ,With i lightend from 7,6 to 3,8kg.
Last edited by mielko on September 24th, 2012, 12:56 pm, edited 10 times in total.
- mielko
- Projects
- Posts: 336
- Joined: January 5th, 2010, 12:39 pm
- Province/State: Europe,holland
So ,introducing my honda,
Its a 1976 1200 EB1 hondamatic.With is except from a home made 54MM stainless exhaust ,bone stock.
Previous ownes has restored it,and is stil in pretty good condition.Although the rust monster is still under its skinn in some parts .
Interior:
its getting a meter console,with narrow band lamda meter,so i can set the carburetor jets ,as i'm going to put some motorcycle carburetor on,in the far future.
Steering wheel of unknown mark,28cm,yes that is small :roll:
Engine is still a EB1,i had it on the dyno,and it made 21,6hp on the wheels
Not realy what i wanted to be,the valva cover reveals some sludge,so i think the head gasket has had its time.
I bought a EB3 ,for spare parts ,with a EB3 engine,i'm going to rebuilt that engine.
Its a 1976 1200 EB1 hondamatic.With is except from a home made 54MM stainless exhaust ,bone stock.
Previous ownes has restored it,and is stil in pretty good condition.Although the rust monster is still under its skinn in some parts .
Interior:
its getting a meter console,with narrow band lamda meter,so i can set the carburetor jets ,as i'm going to put some motorcycle carburetor on,in the far future.
Steering wheel of unknown mark,28cm,yes that is small :roll:
Engine is still a EB1,i had it on the dyno,and it made 21,6hp on the wheels
Not realy what i wanted to be,the valva cover reveals some sludge,so i think the head gasket has had its time.
I bought a EB3 ,for spare parts ,with a EB3 engine,i'm going to rebuilt that engine.
Last edited by mielko on January 7th, 2010, 9:24 am, edited 1 time in total.
- mielko
- Projects
- Posts: 336
- Joined: January 5th, 2010, 12:39 pm
- Province/State: Europe,holland
- joshuao
- Mugen
- Posts: 667
- Joined: February 14th, 2006, 1:07 am
- Province/State: Queensland Australia
- Blackbullet
- Projects
- Posts: 1992
- Joined: July 30th, 2008, 2:03 pm
- Province/State: ..
- mielko
- Projects
- Posts: 336
- Joined: January 5th, 2010, 12:39 pm
- Province/State: Europe,holland
A friend i me was going to weld the original bold holes,onley we found out that these rims have hardend inserts in the bold hole,and did not want to force them out,so i'l leave it this way.
I bought 165/60/13 for the front end,and 175/50/13 pirellie tires,i'l try a test fit this week maybe.If it works ,the are gonna be pouwdercouted in bronze colour.
The rims are 13" 6J ,ET30,if et 30 is to far out,I can machiene them to et35 and stil be strong
The down pipe is from the original cast piece back,into home made absorber,into harley davidson fishtail end :D .Just for fun now.
Complete system is 52mm stainles pipe.
I,m gonna build a header later.
But other prioratie's firs.
I bought 165/60/13 for the front end,and 175/50/13 pirellie tires,i'l try a test fit this week maybe.If it works ,the are gonna be pouwdercouted in bronze colour.
The rims are 13" 6J ,ET30,if et 30 is to far out,I can machiene them to et35 and stil be strong
The down pipe is from the original cast piece back,into home made absorber,into harley davidson fishtail end :D .Just for fun now.
Complete system is 52mm stainles pipe.
I,m gonna build a header later.
But other prioratie's firs.